VOLVO
ECM-U012008 - Lost Communication with Starter/ Generator Control Module. General Failure Information. Bus Signal / Message Failures
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) communicates with the alternator control module (ACM) over LIN. The code is set when the communication is faulty, or when the alternator control module sends fault information to the engine control module. Although the code is titled lost communication with the starter/generator control module, it concerns communication between the engine control module and the alternator control module.
Mulige årsaker
- Contact resistance or oxidation in the connectors
- Open circuit in the signal wire
- Faulty alternator control module (ACM)
- Faulty alternator
Hva du kan gjøre
- 1Check that the fuses are intact
- 2Check the connectors at the alternator control module for contact resistance and oxidation
- 3Look for breaks, chafing or pinched areas on the signal wire between the engine control module and the alternator control module. Use a multimeter to check that the wire has no break
- 4Clear the code and road test the car. If you have a diagnostic tool, check that the code's diagnostic status shows the fault is no longer present
- 5If the fault returns: have a workshop with diagnostic equipment check the alternator and its control module
Symptomer du kan merke1
- The engine does not start
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.