VOLVO
ECM-U030000 - Internal Control Module Software Incompatibility. General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
14 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (17)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Kun motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle motorer unntatt: B5254T7
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2007–2010Kun motor: B6324S
- Volvo XC90 (2003–)2011–2012Kun motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle motorer unntatt: B5254T9
Hva betyr feilkoden?
The engine control module (ECM) compares its own configuration ID with the ID that the central electronics control module (CEM) sends out on the CAN network. The code is set when the IDs do not match, and also when communication with the CEM is or has been interrupted. Although the code is titled internal software incompatibility, it concerns a configuration ID that does not match the CEM.
Mulige årsaker
- Wrong configuration ID because the module is not intended for the car, for example a used module with different software or hardware
- Break in the CAN wires between the engine control module and the CEM
- Intermittent breaks on one or both CAN wires
Hva du kan gjøre
- 1Read the codes in the central electronics control module and other control modules, and fix communication faults first
- 2Check that the fuses are intact
- 3Check the CAN connectors for contact resistance and oxidation
- 4Look for chafed CAN wires. Use a multimeter to check that they have no break or short to ground or supply voltage
- 5If the module was recently replaced: have a workshop check that it is intended for this car and has the correct software and configuration
Symptomer du kan merke5
- The cruise control does not work at all
- The engine jerks on throttle and sharply after engine braking
- Uneven idle
- The engine does not start
- The general warning lamp is on
Hva feilen kan påvirke2
- The module shuts off from the CAN network (bus-off) and stops sending messages
- The module's functions stop working
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.