VOLVO
ECM-U200581 - Vehicle Speed. Bus Signal / Message Failures. Invalid serial data received
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) receives the vehicle speed from the brake control module (BCM) over CAN. The code is set when an expected message from the BCM is missing. The fault may lie in the CAN connections, in the wiring, or in either of the two control modules.
Mulige årsaker
- Contact resistance in the CAN connections
- Open circuit in one or both CAN cables
- One or both signal cables are short-circuited to ground, to voltage or to each other
- Damaged brake control module (BCM)
- Damaged engine control module (ECM)
Hva du kan gjøre
- 1Read the fault codes in the engine control module. If any of ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 is stored, investigate it first.
- 2Read the fault codes in the brake control module (BCM). Any communication faults there should be investigated first, as this code is then a follow-on fault.
- 3Check that the connectors in the CAN network between the BCM and the engine control module are secure and clean, and look for chafed wiring.
- 4Do not work on the brake system yourself. Have a workshop check the BCM if the code returns.
Symptomer du kan merke1
- The check engine lamp lights up or behaves abnormally
Hva feilen kan påvirke1
- The BCM's speed signal is replaced by a substitute value
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.