VOLVO
ECM-U210000 - Initial Configuration Not Complete. General Failure Information. No sub type information
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Feilkoden har ulik betydning avhengig av modell, årsmodell eller motor. Velg betydningen som gjelder din bil.
Gjelder følgende modeller:
10 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–)
Vis modeller per årsmodell og motor (15)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Kun motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle motorer unntatt: B5254T7
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015Kun motor: D4162T
- Volvo S80 (2007–)2008–2010Kun motor: D4204T
- Volvo S80 (2007–)2012–2015Kun motor: D4162T
- Volvo V40 (2013–)2013–2015Kun motor: D4162T
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: D4162T
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012Kun motor: D4162T
- Volvo V60 (2011–)2013–2014Kun motor: D4162T, D82PHEV
- Volvo V60 (2011–)2015Kun motor: D4162T, D82PHEV, D87PHEV
- Volvo V70 (2008–)2008–2010Kun motor: D4204T
- Volvo V70 (2008–)2012–2015Kun motor: D4162T
Hva betyr feilkoden?
The engine control module (ECM) receives information about the vehicle configuration from the central electronic module (CEM). The code is set when that information is incorrect or missing. If the code was set only once and no faults are found after several drive cycles, it most likely came from a software update.
Mulige årsaker
- Fault in the central electronic module (CEM)
- The code can be set during a software update
- Open circuit in the CAN network
- Communication cable short-circuited to ground
- Communication cable short-circuited to supply voltage
- Contact resistance, oxidation or poor contact in the connections
Hva du kan gjøre
- 1Read the fault codes in the central electronic module (CEM) and remedy them first. This code can be erased only once the CEM fault is remedied and erased.
- 2If the code was set once after a software update and does not return, erase it without further action.
- 3Check that the connectors to the CAN network are secure and clean, and look for loose or chafed wiring.
- 4If the code returns, have a workshop read the fault counter and troubleshoot the CAN network with diagnostic equipment.
Symptomer du kan merke2
- Warning symbol and message in the display
- Cruise control cannot be engaged
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.