VOLVO
ECM-U210883 - Adaptive Cruise Control. Bus Signal / Message Failures. Value of signal protection calculation incorrect
System
Motorstyring (ECM)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
7 modellerS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Vis modeller per årsmodell og motor (20)
- Volvo S60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Kun motor: B4204T6
- Volvo S80 (2007–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Kun motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Kun motor: B4164T
- Volvo V40 (2013–)2013Kun motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Kun motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Kun motor: B4164T
- Volvo V60 (2011–)2011Kun motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Kun motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Kun motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Kun motor: B4204T6
- Volvo V70 (2008–)2011Kun motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Kun motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Kun motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Kun motor: B4204T6
- Volvo XC60 (2009–)2011–2012Kun motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Kun motor: B4204T7
Hva betyr feilkoden?
The engine control module (ECM) receives signals from the central electronic module (CEM) over CAN that cover the steering wheel controls for adaptive cruise, and checks the communication. The code is set when communication with the CEM is lost. Although the fault is named a checksum problem, the signal from the CEM is in fact missing.
Mulige årsaker
- Open circuit in the communication cable
- Communication cable short-circuited to ground
- Communication cable short-circuited to supply voltage
- Contact resistance or oxidation in the connections
- Open circuit in the connections
- Short-circuit in the connections
Hva du kan gjøre
- 1The code points to a fault in the CEM. Read out its fault codes and remedy them first.
- 2Read the engine control module codes. If any of ECM-U010482, ECM-P193582, ECM-P080582 or ECM-U042600 is stored, check it first.
- 3Check that the connectors in the CAN network are secure and clean, and look for chafed wiring.
- 4Erase the fault codes once the fault is remedied, then check on a test drive whether the code returns.
Symptomer du kan merke1
- Cruise control cannot be engaged
Hva feilen kan påvirke1
- Cruise control is turned off while the fault is active
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.