VOLVO
SAS-U300362 - Battery Voltage. Algorithm Based Failures. Signal compare failure
System
Rattvinkelsensor (SAS)
Volvo-modeller feilkoden gjelder for
Gjelder følgende modeller:
14 modellerC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Vis modeller per årsmodell og motor (19)
- Volvo C30 (2007–2013)2011–2013Kun motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Kun motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle motorer unntatt: B5254T7
- Volvo S40 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Kun motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
- Volvo XC90 (2003–)2005–2006Kun motor: B8444S
- Volvo XC90 (2003–)2007–2010Kun motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Kun motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012Kun motor: B6324S5
- Volvo XC90 (2003–)2013–2014Alle motorer unntatt: B5254T9
Hva betyr feilkoden?
Although the code is named battery voltage, it applies when the steering angle sensor compares its voltage with that of the central electronic module (CEM) and the two do not agree. The cause can be poor contact or oxidation at the connector on the steering wheel module, or an internal fault in the sensor.
Mulige årsaker
- Poor contact or oxidised connector on the steering wheel module (SWM).
- Internal malfunction within the sensor (SAS).
Hva du kan gjøre
- 1Clear the code and test drive the car. It mainly needs action if it has been active a long time and a function is lost.
- 2With a diagnostic tool and the ignition on, compare the voltage values of the steering angle sensor and the CEM. They should be roughly the same.
- 3Check that the fuses are intact and that the connectors to the steering wheel module are firmly seated and not corroded.
- 4Have a workshop replace the contact reel or angle sensor if the fault returns. If the code comes back after that, the steering wheel module (SWM) must be replaced.
- 5The angle sensor is part of the steering and stability system. Have a workshop carry out the checks and repair rather than working on the steering wheel yourself.
Symptomer du kan merke5
- The information lamp lights up
- The anti-spin warning lamp lights up
- Traction control and the stability function do not work
- The Four-C function does not work
- A yellow warning symbol and text message show in the display
Hva feilen kan påvirke2
- The stability function is blocked
- The sensor warns the other control modules that the data it sends is wrong
Generell veiledning for bileiere. Feilsøking på bilen kan peke på en annen årsak.