BCM-C001D01 - Right Rear Outlet Control. General Failure Information. General electrical failure
System
Bremssteuergerät (BCM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
13 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (16)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2012
- Volvo V60 (2011–)2013–2014Alle Motoren außer: D82PHEV
- Volvo V60 (2011–)2015Alle Motoren außer: D82PHEV, D87PHEV
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
Was bedeutet der Fehlercode?
The brake control module (BCM) has detected an electrical fault in one of the valve coils in the hydraulic unit, in this case the outlet valve for the right rear wheel. The outlet valve releases brake pressure from the wheel, and if the signal from the coil is too low, too high or missing, the module cannot regulate braking correctly. The fault can only be detected once the module's test has started with the ignition on.
Mögliche Ursachen
- Internal fault in the brake control module
- Poor contact or corrosion at the connector on the hydraulic unit or the module
- Open or short circuit in the wire to the valve coil
- Temporary electrical interference that makes the module's calculation incorrect
Was Sie tun können
- 1Read and note the code, clear it and road test the car to see whether it returns
- 2Check that the battery is in good condition and that its terminals are tight, as low voltage can cause false internal faults
- 3Check the brake system fuses and that the connectors at the brake control module are secure and free from corrosion
- 4With diagnostic equipment activate the hydraulic unit valves and check that they respond
- 5If the fault returns despite this, the brake control module normally needs replacing by a workshop
- 6Do not work on the brake hydraulic unit or the module yourself; leave this to a workshop. The brakes still work but without ABS, so drive carefully until the fault is fixed
Symptome, die Sie bemerken können5
- Information lamp lit
- General warning lamp and brake system warning lamp on
- Traction control, stability control and anti-skid function do not work
- Adaptive cruise control, collision warning and auto brake do not work
- Yellow warning symbol or red symbol with a message in the display
Was der Fehler beeinflussen kann2
- Active yaw control (AYC) is blocked
- ABS, traction control, stability control and brake assistance can be disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.