BCM-U042862 - Invalid Data Received From Steering Angle Sensor Module. Algorithm Based Failures. Signal compare failure
System
Bremssteuergerät (BCM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
13 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (14)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T, D5204T, D5204T5
- Volvo C70 (2006–2013)2011Nur Motor: D5204T, D5204T5
- Volvo C70 (2006–2013)2012–2013Alle Motoren außer: B5254T7
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo S60 (2011–)2011–2015
- Volvo S80 (2007–)2007–2015
- Volvo V40 (2013–)2013–2015
- Volvo V40 Cross Country (2013–)2013–2015
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T, D5204T, D5204T5
- Volvo V60 (2011–)2011–2015
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2015
- Volvo XC60 (2009–)2009–2015
- Volvo XC70 (2008–)2008–2015
Was bedeutet der Fehlercode?
At each new ignition cycle the brake control module (BCM) compares the steering angle from the steering angle sensor with a calculated value. The code is set when the difference between the two values is too large, which most often happens when the steering angle sensor has not been initialised during a longer drive. It applies to cars with a stability system and can be set when stability has been regulated for too long.
Mögliche Ursachen
- The driver has driven for a long time with an uninitialised steering angle sensor after start-up
- The driver drove with an uninitialised steering angle sensor and then switched the ignition off
- Internal fault in the steering angle sensor control module (SAS)
Was Sie tun können
- 1If other codes are stored in the module, troubleshoot them first
- 2Check the front wheel alignment and have a workshop adjust it if needed
- 3Think back on whether the car has been driven for a long time without the steering wheel being turned after start-up
- 4The brake and stability systems are safety-critical, so have a workshop carry out any work on the steering angle sensor and the brake control module
Symptome, die Sie bemerken können5
- Traction and anti-skid warning lamp lit
- Stability function does not work
- Traction control does not work
- Anti-skid function does not work
- Adaptive cruise control does not work
Was der Fehler beeinflussen kann3
- Stability control is disabled
- Traction control is disabled
- Dynamic stability control (AYC) is disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.