Zum Inhalt springen
    OBD Tuning
    SENDEN SIE AN UNS
    SENDEN SIE AN UNS
    Startseite
    Fehlercodes
    VOLVO
    CEM-8A24
    VOLVO

    CEM-8A24 - Gas discharge lamp module (GDL) left-hand. Faulty signal

    System

    Zentralelektronik (CEM)

    Volvo-Modelle, für die dieser Fehlercode gilt

    Gilt für folgende Modelle:

    4 Modelle

    C30 (2007–2013), C70 (2006–2013), S40 (2004–2013), V50 (2004–2013)

    Modelle nach Baujahr und Motor anzeigen (4)
    • Volvo C30 (2007–2013)2007–2011
    • Volvo C70 (2006–2013)2006–2011
    • Volvo S40 (2004–2013)2004–2007
    • Volvo V50 (2004–2013)2004–2007

    Was bedeutet der Fehlercode?

    Although the code is named faulty signal, the left-hand gas discharge lamp module (GDL) reports an internal fault to the central electronic module (CEM). The fault may lie in the module, in the lamp housing or in the signal wiring between them. Check the lamp and the wiring before the module is replaced.

    Mögliche Ursachen

    • The left-hand gas discharge lamp module (GDL) is faulty
    • The left-hand lamp housing is faulty
    • Open circuit in the signal wire between the left-hand lamp housing and the gas discharge lamp module
    • The signal wire between the lamp housing and the module is short-circuited to battery voltage
    • The signal wire between the lamp housing and the module is short-circuited to ground

    Was Sie tun können

    1. 1Switch on the low beam and see whether the left lamp lights. If it does not, check the bulb first and replace it with a new one of the correct type
    2. 2Switch the ignition off and unplug the connectors to the headlamp. Check that they are not oxidised, loose or damaged
    3. 3Use a multimeter to check that the signal wires between the lamp housing and the module are not broken and have no contact with ground or battery voltage
    4. 4After recent removal or replacement, make sure the igniter sits properly. It works on high voltage, so leave other work to a workshop
    5. 5If the fault remains, have a workshop replace the module. After replacement the car data must be programmed in and the position sensors recalibrated

    Symptome, die Sie bemerken können1

    • The low beam does not work

    Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.

    OBD Tuning

    Schwedens führendes Kompetenzzentrum für Automotorelektronik. Wir bieten professionelle ECU-Optimierung, Steuergerätereparatur und Diagnose mit 12-monatiger Garantie.

    Dienstleistungen

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    Datenbank & Diagnose

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    ECU-Hersteller

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Unternehmen

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    Besuchen Sie uns

    Gjuterigatan 29, Karlstad

    Rufen Sie uns an

    054-830 480

    Schreiben Sie uns eine E-Mail

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Alle Rechte vorbehalten.