Zum Inhalt springen
    OBD Tuning
    SENDEN SIE AN UNS
    SENDEN SIE AN UNS
    Startseite
    Fehlercodes
    VOLVO
    CEM-B10BF11
    VOLVO

    CEM-B10BF11 - Seat Belt Reminder Indicator. General Electrical Failures. Circuit short to ground

    System

    Zentralelektronik (CEM)

    Volvo-Modelle, für die dieser Fehlercode gilt

    Gilt für folgende Modelle:

    7 Modelle

    S60 (2011–), S80 (2007–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)

    Modelle nach Baujahr und Motor anzeigen (7)
    • Volvo S60 (2011–)2011–2015
    • Volvo S80 (2007–)2007–2015
    • Volvo V60 (2011–)2011–2015
    • Volvo V60 Cross Country (2015–)2015
    • Volvo V70 (2008–)2008–2015
    • Volvo XC60 (2009–)2009–2015
    • Volvo XC70 (2008–)2008–2015

    Was bedeutet der Fehlercode?

    The CEM supplies the seat belt reminder lamp with power. The code is stored when the module detects that the signal from the output is too low, which is caused by the signal cable being short-circuited to ground. The seat belt reminder lamp then does not light.

    Mögliche Ursachen

    • The signal cable to the seat belt reminder lamp is short-circuited to ground

    Was Sie tun können

    1. 1Read and note the code, clear it, then check whether the seat belt reminder lamp lights again when you start the car
    2. 2Check that the relevant fuses are intact. Their locations are in the owner's manual or on the fuse box cover
    3. 3Look for chafing on the lamp wiring, especially where it may have been pinched
    4. 4Check that the connectors on the lamp wiring are secure and free from corrosion
    5. 5If the fault returns, have a workshop with diagnostic equipment check the wiring and the control module

    Symptome, die Sie bemerken können1

    • The seat belt reminder lamp does not light

    Was der Fehler beeinflussen kann3

    • The output switches off during the driving cycle in which the fault is detected
    • If the fault remains, the output switches off permanently after 100 driving cycles
    • Clearing the code and starting a new driving cycle resets the output

    Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.

    OBD Tuning

    Schwedens führendes Kompetenzzentrum für Automotorelektronik. Wir bieten professionelle ECU-Optimierung, Steuergerätereparatur und Diagnose mit 12-monatiger Garantie.

    Dienstleistungen

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    Datenbank & Diagnose

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    ECU-Hersteller

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Unternehmen

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    Besuchen Sie uns

    Gjuterigatan 29, Karlstad

    Rufen Sie uns an

    054-830 480

    Schreiben Sie uns eine E-Mail

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Alle Rechte vorbehalten.