VOLVO
ECM-1360 - Intake air temperature (IAT) sensor. Signal too low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
8 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo C30 (2007–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Nur Motor: D5244T8
- Volvo S40 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Nur Motor: D5244T8
- Volvo V50 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Nur Motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2008–2010Nur Motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Nur Motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle Motoren außer: B5254T2, B6324S5
Was bedeutet der Fehlercode?
The ECM watches the reading from the temperature sensor inside the MAF sensor. The fault is set when that signal is faulty. Although the code is labelled too low, a too high signal from a short to voltage can also set it.
Mögliche Ursachen
- Signal wire shorted to voltage
- Damaged intake air temperature sensor inside the MAF sensor
- Contact resistance or oxidation in the connections
- Signal wire shorted to ground
Was Sie tun können
- 1Read the fault code, clear it and test drive to see whether it returns
- 2Check the MAF sensor connector for contact resistance, play and oxidation
- 3Check the wiring to the MAF sensor for a short to ground, since it can give too low a signal
- 4With a multimeter, check that the signal wire is not shorted to voltage or ground
- 5If you have a diagnostic tool: read the temperature in live data and check that it is reasonable and follows engine warm-up
- 6If the connection and wiring are fine: have a workshop check the MAF sensor
Symptome, die Sie bemerken können1
- Engine warning lamp comes on
Was der Fehler beeinflussen kann1
- The engine control uses a calculated value instead of the sensor
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.