VOLVO
ECM-2890 - Lambda control. Faulty signal
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
8 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo C30 (2007–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Nur Motor: D5244T8
- Volvo S40 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Nur Motor: D5244T8
- Volvo V50 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Nur Motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2008–2010Nur Motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Nur Motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle Motoren außer: B5254T2, B6324S5
Was bedeutet der Fehlercode?
The engine control module monitors the pump current of the oxygen sensor. The code is set when current is detected in the pump current circuit while the sensor is cold, which points to leakage current or flashover in the wiring. The fault can also come from an internal fault in the control module.
Mögliche Ursachen
- Short circuit or flashover in the pump current wires
- Fault inside the engine control module (ECM) itself
Was Sie tun können
- 1Let the car stand until cold, start the engine and see whether the code returns
- 2With the car switched off, use a multimeter to check that the pump current wires have no contact with each other or with other wires
- 3Look for chafed wires and for moisture or dirt at the oxygen sensor connector, which can cause leakage current
- 4If the wires are intact but the fault remains, have a workshop check the control module with diagnostic equipment
Symptome, die Sie bemerken können1
- Message in the information display
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.