VOLVO
ECM-28A0 - Heated oxygen sensor (HO2S). Signal too low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
8 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo C30 (2007–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Nur Motor: D5244T8
- Volvo S40 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Nur Motor: D5244T8
- Volvo V50 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Nur Motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2008–2010Nur Motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Nur Motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle Motoren außer: B5254T2, B6324S5
Was bedeutet der Fehlercode?
Although the code is named signal too low, the control module has calculated an incorrect temperature for the oxygen sensor from its internal resistance, and the code is set when that calculated value is wrong. Causes may be a broken or shorted signal wire, a damaged sensor, or an internal fault in the control module.
Mögliche Ursachen
- Open circuit in the signal cable
- Short circuit between the signal cables
- Damaged oxygen sensor
- Fault inside the engine control module (ECM) itself
Was Sie tun können
- 1Read the code, clear it and run the engine for a while to see whether it returns
- 2Switch off the ignition and check the oxygen sensor connections: they should be secure and free from play, contact resistance and oxidation
- 3With the car switched off, use a multimeter to check that the signal wire is not broken and the two signal wires are not shorted to each other
- 4If the connections and wiring are in order but the fault remains, have a workshop check the sensor and the control module with diagnostic equipment
Symptome, die Sie bemerken können1
- Message in the information display
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.