VOLVO
ECM-340D - Camshaft position sensor, intake. Signal too low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
The intake side camshaft position sensor sends a signal that stays at too low a level. The control module interprets this as a fault and sets the code. The causes may be a short to ground in the signal wire, an open circuit in the supply wire or a loose connection. The engine may be hard to start.
Mögliche Ursachen
- Signal wire shorted to ground
- Open circuit in the supply wire to the sensor
- Loose connection
Was Sie tun können
- 1Clear the code and restart the engine to see whether it returns
- 2Check that the intake camshaft sensor connector is secure and clean
- 3Use a multimeter to check that the signal wire has no contact with ground
- 4Use a multimeter to confirm the supply wire to the sensor is intact, with no open circuit
- 5If the fault remains, have a workshop check the camshaft sensor with diagnostic equipment
Symptome, die Sie bemerken können1
- The engine is difficult to start
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.