VOLVO
ECM-341B - Camshaft position (CMP) sensor, exhaust. Signal missing
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
The exhaust side camshaft position sensor occasionally gives no signal, although the signal then returns. The control module treats this as a fault and sets the code. The engine may be hard to start.
Mögliche Ursachen
- Camshaft position sensor in the wrong position
- Damaged camshaft position sensor
- Loose connection
- Camshafts incorrectly adjusted
Was Sie tun können
- 1Start the engine, raise the speed a few times, then read the code
- 2Check that the exhaust camshaft sensor connector is fastened and free from oxidation
- 3Check that the sensor is correctly fitted and not damaged around its housing
- 4If you have a diagnostic tool: read the fault status; "Fault found" means a permanent fault, "No fault found" means it is not active at the moment
- 5Have a workshop check the camshaft angle against the crankshaft with diagnostic equipment
Symptome, die Sie bemerken können1
- The engine is difficult to start
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.