VOLVO
ECM-432B - Leak diagnostic unit, valve. Signal missing
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
The engine control module expects a signal from the valve in the leak diagnostic pump when the valve is activated. If the signal is missing, the fault code is set and the leak diagnostic is disabled. The fault can be caused by poor contact, an open circuit in the signal or supply wire, or a damaged valve in the leak diagnostic unit.
Mögliche Ursachen
- Contact resistance in the connections
- Open circuit in the signal wire
- Open circuit in the supply wire
- Damaged valve
- Damaged valve in the leak diagnostic unit
Was Sie tun können
- 1Have you got a diagnostic tool: switch the valve on with the ignition on and listen for a click when it is activated
- 2Check the fuse for the circuit
- 3Check the leak diagnostic unit connector for contact resistance and oxidation
- 4Use a multimeter to check that the signal and supply wires are not open-circuited
- 5Have a workshop replace the leak diagnostic unit if the fuse and wiring are intact but the fault remains
Symptome, die Sie bemerken können1
- Malfunction indicator lamp (MIL) is on
Was der Fehler beeinflussen kann1
- The leak diagnostic is disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.