VOLVO
ECM-500B - Engine speed (RPM) sensor signal. Signal missing
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
The engine speed sensor at the flywheel gives the engine control module the top dead centre (TDC) position. If the signal is missing so that the position cannot be read, the code is set, and it shows when the engine runs.
Mögliche Ursachen
- Contact resistance and oxidation in the engine speed sensor connector
- Intermittent faults in the engine speed sensor wiring
- Incorrectly installed engine speed sensor
- Signal interference from nearby cables
Was Sie tun können
- 1Make sure the engine speed sensor is correctly fitted and free from damage and contamination
- 2Check that the connector to the engine speed sensor is firmly seated and clean
- 3Check whether the starter motor cable or other high-current cables run too close to the sensor wiring
- 4Have a workshop examine the flywheel for damage if the signal is still missing
Symptome, die Sie bemerken können2
- Engine is difficult to start
- Poor performance
Was der Fehler beeinflussen kann2
- The camshaft position sensor signal is used instead if it has been adapted
- Variable valve timing (VVT) control is blocked
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.