VOLVO
ECM-8420 - Sensor supply 2. Signal too low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
8 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008, 2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo C30 (2007–2013)2009Nur Motor: D4164T, D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Nur Motor: D5244T8
- Volvo S40 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008, 2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2009Nur Motor: D4164T, D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Nur Motor: D5244T8
- Volvo V50 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008, 2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo V50 (2004–2013)2009Nur Motor: D4164T, D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Nur Motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2008–2010Nur Motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Nur Motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle Motoren außer: B5254T2, B6324S5
Was bedeutet der Fehlercode?
The engine control module (ECM) monitors the supply voltage to the engine sensors and sets the code when it is too low or too high. The check runs with the ignition on. This variant applies to a supply that is too low, which can come from an open circuit, poor contact or a short to ground in the supply wire.
Mögliche Ursachen
- Loose connection, contact resistance or oxidation in the connections
- Open circuit in the voltage supply wire
- Short to ground in the voltage supply wire
Was Sie tun können
- 1Read the code, clear it and check that it is not active after the road test
- 2Check the sensor supply connectors for loose fit, contact resistance and oxidation
- 3Check the supply wire for an open circuit, and use a multimeter to confirm it has no contact with ground (the body)
- 4If you have diagnostic equipment, read the sensor supply voltage in live data with the ignition on and see whether it is too low
- 5If the fault remains after these checks, have a workshop trace the sensors and the control module further
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.