VOLVO
ECM-8510 - Starter motor signal. Signal too low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
8 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo C30 (2007–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C30 (2007–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo C70 (2006–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo C70 (2006–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S40 (2004–2013)2006Nur Motor: D5244T8
- Volvo S40 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo S40 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo S60 (2001–2009)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo S60 (2001–2009)2007–2009Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V50 (2004–2013)2006Nur Motor: D5244T8
- Volvo V50 (2004–2013)2007Nur Motor: D5244T8, D5244T9
- Volvo V50 (2004–2013)2008–2010Nur Motor: D5244T13, D5244T8, D5244T9
- Volvo V70 (2000–2008)2006Nur Motor: D5244T4, D5244T5, D5244T6, D5244T7
- Volvo V70 (2000–2008)2007Nur Motor: D5244T4, D5244T5, D5244T7
- Volvo V70 (2000–2008)2008Nur Motor: D5244T5, D5244T7
- Volvo V70 XC / XC70 (2001–2007)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2006–2007Nur Motor: D5244T4
- Volvo XC90 (2003–)2008–2010Nur Motor: D5244T4, D5244T5
- Volvo XC90 (2003–)2011Nur Motor: D5244T18, D5244T4, D5244T5
- Volvo XC90 (2003–)2012Alle Motoren außer: B5254T2, B6324S5
Was bedeutet der Fehlercode?
The ECM feeds the start relay a signal at engine start, and that signal controls the starter motor. The code is set when the control module detects that the signal is too low. A short to ground in the signal wire is a possible cause.
Mögliche Ursachen
- The signal wire is shorted to ground
Was Sie tun können
- 1With the ignition off, check the connectors in the signal circuit for loose fit and oxidation
- 2Use a multimeter to check that the signal wire to the start relay is not shorted to ground (the body)
- 3Check that the signal wire is not chafed or pinched where it runs near the body or moving parts
- 4Repair as needed and road test the car to see whether the code returns
- 5If the fault remains after these checks, have a workshop trace the control module and the start relay further
Symptome, die Sie bemerken können2
- The engine does not start
- A message appears in the information display
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.