ECM-913F - Throttle position (TP). Non plausible request
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
9 ModelleC70 Cabriolet (1998–2005), C70 Coupé (1998–2002), S60 (2001–2009), S70 (1997–2000), S80 (1999–2006), V70 (1997–2000), V70 (2000–2008), V70 XC (1998–2000), V70 XC / XC70 (2001–2007)
Modelle nach Baujahr und Motor anzeigen (22)
- Volvo C70 Cabriolet (1998–2005)1999–2002
- Volvo C70 Coupé (1998–2002)1999–2002
- Volvo S60 (2001–2009)2001Alle Motoren außer: D5244T
- Volvo S60 (2001–2009)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S60 (2001–2009)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S60 (2001–2009)2006–2008Nur Motor: B5244SG
- Volvo S70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5254S DENSO, B5254T
- Volvo S70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)1999–2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo S80 (1999–2006)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S80 (1999–2006)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S80 (1999–2006)2006Nur Motor: B5244SG
- Volvo V70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5234T8, B5254S DENSO, B5254T
- Volvo V70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo V70 (2000–2008)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo V70 (2000–2008)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo V70 (2000–2008)2006–2008Nur Motor: B5244SG
- Volvo V70 XC (1998–2000)1999–2000
- Volvo V70 XC / XC70 (2001–2007)2001
Was bedeutet der Fehlercode?
The throttle module (ETM) checks that the engine control module (ECM) requests a feasible throttle position and has time to complete its calculations in each work cycle. If the request is infeasible or the ECM does not respond as expected, the code is set. The cause can be a defective engine control module or an inadequate power supply to it.
Mögliche Ursachen
- Defective engine control module
- Inadequate power supply to the engine control module
Was Sie tun können
- 1Check the battery condition and voltage at start-up, as low voltage can be an external cause of the fault
- 2If you have a diagnostic tool: read when the fault was recorded and how often. If it has happened several times without an external cause, the engine control module may be defective
- 3Check that the correct software is in the throttle unit and the engine control module, as software that does not match can set the code. Have a workshop check this
- 4Erase the codes and reset: ignition off for three minutes, on and off again, then three more. Add two minutes if the cooling fan has been running.
- 5If the fault returns without an external cause, have a workshop replace and check the engine control module
Symptome, die Sie bemerken können4
- The accelerator pedal is ignored when the brake pedal is pressed
- The cruise control cannot be activated
- The idle is uneven and the car jerks during engine braking
- The ETS warning lamp lights, on C70 and S/V70 -2000 only
Was der Fehler beeinflussen kann3
- The throttle follows the accelerator pedal position, and engine speed is controlled by fuel cut-off with the injectors switched off one at a time
- The cruise control is switched off during the driving cycle when the fault is present, and it works again the next time the car starts if the fault is gone
- Braking closes the throttle, and pedal input is ignored while the brake is pressed
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.