ECM-9180 - Accelerator pedal (AP) position sensor. Faulty signal
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
9 ModelleC70 Cabriolet (1998–2005), C70 Coupé (1998–2002), S60 (2001–2009), S70 (1997–2000), S80 (1999–2006), V70 (1997–2000), V70 (2000–2008), V70 XC (1998–2000), V70 XC / XC70 (2001–2007)
Modelle nach Baujahr und Motor anzeigen (22)
- Volvo C70 Cabriolet (1998–2005)1999–2002
- Volvo C70 Coupé (1998–2002)1999–2002
- Volvo S60 (2001–2009)2001Alle Motoren außer: D5244T
- Volvo S60 (2001–2009)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S60 (2001–2009)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S60 (2001–2009)2006–2008Nur Motor: B5244SG
- Volvo S70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5254S DENSO, B5254T
- Volvo S70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)1999–2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo S80 (1999–2006)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S80 (1999–2006)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S80 (1999–2006)2006Nur Motor: B5244SG
- Volvo V70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5234T8, B5254S DENSO, B5254T
- Volvo V70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo V70 (2000–2008)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo V70 (2000–2008)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo V70 (2000–2008)2006–2008Nur Motor: B5244SG
- Volvo V70 XC (1998–2000)1999–2000
- Volvo V70 XC / XC70 (2001–2007)2001
Was bedeutet der Fehlercode?
The throttle unit (ETM) has found a problem with the PWM signal coming from the pedal sensor, and the engine control module (ECM) stores the code. The fault can be a signal that is too high or too low, or a signal cable that is open or short-circuited. The code is always set together with ECM-918F and is therefore troubleshot according to that code.
Mögliche Ursachen
- Signal cable short-circuited to the supply
- Signal cable short-circuited to ground
- Open circuit in the signal cable
- Loose connections
- Defective accelerator pedal sensor
Was Sie tun können
- 1First remedy fault code ECM-918F, as this code is always set together with ECM-9180
- 2Check the connector at the accelerator pedal sensor and the engine control module for loose connections and oxidation
- 3Use a multimeter to check that the signal cable from the accelerator pedal sensor has no open circuit and is not short-circuited to ground or voltage
- 4Check the battery condition and charge
- 5If you have a diagnostic tool: follow the accelerator pedal position in live data and check that the value changes smoothly when the pedal is pressed and released
- 6Erase the fault code and test drive. If it returns, have a workshop check the accelerator pedal sensor
Symptome, die Sie bemerken können5
- The accelerator pedal is ignored when the brake pedal is pressed
- The ETS warning lamp lights, on C70 and S/V70 -2000 only
- The idle is uneven and the car jerks during engine braking
- Throttle response is very poor
- Top speed is reduced
Was der Fehler beeinflussen kann2
- The throttle unit switches off its motor control, so the throttle moves to its mechanical stop position and engine speed is controlled by fuel cut-off
- The idle can feel very uneven because engine speed is then controlled by fuel cut-off. This is a result of the reconfiguration and should not be confused with an actual driveability fault
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.