VOLVO
ECM-91DF - Brake pedal position. Faulty position
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC70 Cabriolet (1998–2005), C70 Coupé (1998–2002), S60 (2001–2009), S70 (1997–2000), S80 (1999–2006), V70 (1997–2000), V70 (2000–2008), V70 XC (1998–2000), V70 XC / XC70 (2001–2007)
Modelle nach Baujahr und Motor anzeigen (22)
- Volvo C70 Cabriolet (1998–2005)1999–2002
- Volvo C70 Coupé (1998–2002)1999–2002
- Volvo S60 (2001–2009)2001Alle Motoren außer: D5244T
- Volvo S60 (2001–2009)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S60 (2001–2009)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S60 (2001–2009)2006–2008Nur Motor: B5244SG
- Volvo S70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5254S DENSO, B5254T
- Volvo S70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)1999–2000Alle Motoren außer: D5252T MSA 15.8
- Volvo S80 (1999–2006)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo S80 (1999–2006)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo S80 (1999–2006)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo S80 (1999–2006)2006Nur Motor: B5244SG
- Volvo V70 (1997–2000)1999Nur Motor: B5204T3, B5204T4, B5234T3, B5234T7, B5234T8, B5254S DENSO, B5254T
- Volvo V70 (1997–2000)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2000Alle Motoren außer: D5252T MSA 15.8
- Volvo V70 (2000–2008)2001Alle Motoren außer: D5244T, D5252T MSA 15.8
- Volvo V70 (2000–2008)2002Nur Motor: B5244S, B5244S2, B5244SG, B5244SG2
- Volvo V70 (2000–2008)2003–2005Nur Motor: B5244SG, B5244SG2
- Volvo V70 (2000–2008)2006–2008Nur Motor: B5244SG
- Volvo V70 XC (1998–2000)1999–2000
- Volvo V70 XC / XC70 (2001–2007)2001
Was bedeutet der Fehlercode?
The throttle unit (ETM) compares the brake pedal position from the brake light switch signal with the position the engine control module (ECM) sends on the CAN network. If they differ for too long, the code is set. It can also be stored when CAN communication with the ECM fails.
Mögliche Ursachen
- Power supply to the engine control module
- Open circuit, short-circuit to voltage or short-circuit to ground in the brake light switch signal cable between the ECM and the throttle unit
Was Sie tun können
- 1Use the frozen values and counters of the fault code. If the fault has occurred often recently, it is easier to recreate it during troubleshooting
- 2Check that the engine control module receives power, and that its fuses and earth points are in order
- 3Check the connectors in the brake light switch signal cable for loose connections and oxidation
- 4Use a multimeter to check that the brake light switch signal cable has no open circuit and is not short-circuited to voltage or ground
- 5If the fault remains after a test drive, have a workshop check the CAN communication and whether upgraded software is available for the car
Symptome, die Sie bemerken können3
- The accelerator pedal is ignored when the brake pedal is pressed
- The cruise control cannot be activated
- The ETS warning lamp lights, on C70 and S/V70 -2000 only
Was der Fehler beeinflussen kann3
- The throttle closes when braking, and pedal input is ignored while the brake is pressed
- The cruise control is switched off during the driving cycle when the fault was detected, and it works again the next time the car starts if the fault is gone
- During the driving cycle when the fault is active, no substitute values are generated
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.