VOLVO
ECM-929C - Engine control module (ECM). Signal too high
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
Although the code is titled signal too high, it concerns the ECM's internal governor for the throttle angle. The code is stored when that governor is damaged, or when its control signal reaches an extreme while the throttle is being controlled. The fault may be permanent or sporadic.
Mögliche Ursachen
- The throttle sticks or is blocked by oil film, dust or similar
- Contact resistance or oxidation between the ECM and the throttle unit
- Open circuit, or short to ground or supply voltage, in the throttle motor wiring
- Short circuit between the throttle motor wires
- A damaged throttle unit
- Faulty software in the ECM
Was Sie tun können
- 1If you have a diagnostic tool: read the fault status with the engine running. Fault found means permanent, and No fault found means sporadic and not active right now
- 2Check that the connectors at the throttle unit and the ECM are secure and free from corrosion
- 3Check that the throttle moves freely, is not blocked by any object and is not sticking. Clean as needed
- 4Use a multimeter on the throttle motor wiring after open circuits, contact with ground or plus, and shorts between the wires
- 5If you have a diagnostic tool: check in the parameters that the throttle unit adaptation is complete and shows OK. The adaptation itself is carried out by a workshop
- 6The code can be caused by faulty software in the ECM. Checking and installing new software is a workshop job
Symptome, die Sie bemerken können2
- Malfunction indicator lamp (MIL) on
- Reduced engine performance
Was der Fehler beeinflussen kann1
- The ECM cuts power to the throttle motor so the throttle goes to its return position, or the fuel supply is temporarily shut off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.