VOLVO
ECM-92B0 - Electronic throttle unit. Faulty signal
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
9 ModelleC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (23)
- Volvo C30 (2007–2013)2007Nur Motor: B5254T3
- Volvo C30 (2007–2013)2008–2013Nur Motor: B5254T7
- Volvo C70 (2006–2013)2006–2007Nur Motor: B5254T3
- Volvo C70 (2006–2013)2008–2013Nur Motor: B5254T7
- Volvo S40 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo S40 (2004–2013)2008Nur Motor: B5254T3, B5254T7
- Volvo S40 (2004–2013)2009–2012Nur Motor: B5254T7
- Volvo S60 (2001–2009)2005–2006Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo S60 (2001–2009)2008–2009Nur Motor: B5204T5, B5244T5, B5254T2
- Volvo S80 (1999–2006)2005–2006Nur Motor: B5204T5, B5244T4, B5254T2, B6294S2, B6294T
- Volvo V50 (2004–2013)2005–2007Nur Motor: B5254T3
- Volvo V50 (2004–2013)2008–2012Nur Motor: B5254T7
- Volvo V70 (2000–2008)2005Nur Motor: B5204T5, B5244T4, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2006–2007Nur Motor: B5204T5, B5244T5, B5254T2, B5254T4
- Volvo V70 (2000–2008)2008Nur Motor: B5254T2
- Volvo V70 XC / XC70 (2001–2007)2005Alle Motoren außer: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Nur Motor: B5244T4, B5254T2
- Volvo V70 XC / XC70 (2001–2007)2007Nur Motor: B5254T2
- Volvo XC90 (2003–)2005–2006Nur Motor: B5254T2, B6294T
- Volvo XC90 (2003–)2007–2012Nur Motor: B5254T2
- Volvo XC90 (2003–)2013–2014Nur Motor: B5254T9
- Volvo XC90 (2003–)2015
Was bedeutet der Fehlercode?
The ECM cannot complete the throttle unit's first adaptation, because the programmed limit for the mechanical stop position of the throttle position sensor has been exceeded. Adaptation is normally done at manufacture and must be repeated after a software, ECM or throttle unit change. Although the code is titled faulty signal, it concerns this adaptation.
Mögliche Ursachen
- The throttle sticks or is blocked by oil film or dust
- Contact resistance or oxidation in the connectors between the ECM and the throttle unit
- No new adaptation has been done after a software, ECM or throttle unit change
- A damaged throttle unit
Was Sie tun können
- 1Read the fault codes. Other stored codes should be dealt with first, as they may be why the adaptation cannot be completed
- 2Check the connectors at the throttle unit and the ECM: are they secure and free from corrosion
- 3Check that the throttle is not blocked by any object and not sticking. Clean as needed
- 4If you have a diagnostic tool: check in the parameters whether the throttle unit adaptation shows OK. The adaptation itself is carried out by a workshop
- 5After a software, ECM or throttle unit change the adaptation must be repeated. Have a workshop with diagnostic equipment do this
- 6If the fault remains after this, the throttle unit may be damaged. It would then need replacing, and the new unit must be adapted by a workshop
Symptome, die Sie bemerken können3
- Malfunction indicator lamp (MIL) on
- Reduced performance
- Uneven idle
Was der Fehler beeinflussen kann3
- The ECM falls back on nominal values for the throttle unit's parameters
- The ECM cuts power to the throttle motor, so the throttle goes to its return position
- The ECM may use a reversible fuel shut-off, meaning a temporary one
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.