VOLVO
ECM-P001268 - Intake Camshaft Position Timing - Over-Retarded (Bank 1). Algorithm Based Failures. Event information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (27)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Nur Motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6324S2
- Volvo S80 (2007–)2011–2015Nur Motor: B6324S4
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Nur Motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B6324S2
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6324S4
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
This is an event-based code that is recorded as information and does not indicate a fault in the control module. The engine control module monitors the intake-side VVT valve, bank 1, and the code is set if the valve is too far from its target value for a certain time. The code does not require any action in itself.
Mögliche Ursachen
- No underlying fault that needs correcting, the code is informational
Was Sie tun können
- 1There is no separate troubleshooting for this code, so read it and note it down
- 2If other intake camshaft control codes are present at the same time, troubleshoot those first
Symptome, die Sie bemerken können1
- No noticeable symptoms for the driver
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.