VOLVO
ECM-P001778 - Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B. Mechanical Failures. Alignment or adjustment incorrect
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (27)
- Volvo S60 (2011–)2011Alle Motoren außer: B6304T4, D4162T, D5204T2, D5244T10
- Volvo S60 (2011–)2012Nur Motor: B4164T, B4164T2, B4164T3, B4204T7, B5254T5
- Volvo S60 (2011–)2013–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2007–2008Nur Motor: B5254T6
- Volvo S80 (2007–)2009Nur Motor: B5254T6, B5254T8
- Volvo S80 (2007–)2010Nur Motor: B4204T6, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11, B5254T8
- Volvo S80 (2007–)2012Nur Motor: B4164T, B4164T2, B4204T6, B4204T7, B5254T10
- Volvo S80 (2007–)2013–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2008Nur Motor: B5254T6
- Volvo V70 (2008–)2009Nur Motor: B5254T6, B5254T8
- Volvo V70 (2008–)2010Nur Motor: B4204T6, B5254T10, B5254T11
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7, B5254T10, B5254T11
- Volvo V70 (2008–)2012Nur Motor: B4164T, B4164T2, B4204T7, B5254T10
- Volvo V70 (2008–)2013–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module checks the camshaft positions relative to the crankshaft. The code concerns the exhaust camshaft, bank 1, sensor B, when it sits too far behind the crankshaft and the adaptation falls below a certain value. The fault is checked with the engine warm and at idle.
Mögliche Ursachen
- Incorrectly set camshafts
- Camshaft timing belt has skipped teeth
- Worn teeth on the camshaft belt
- Camshaft incorrectly fitted
- Damaged camshaft
Was Sie tun können
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the engine oil level and quality, and that it is free from contamination
- 3If you have a diagnostic tool: read the exhaust camshaft adaptation with the engine warm and idling
- 4Have a workshop check that the camshaft is fitted correctly and that the timing belt sits correctly without skipped teeth
- 5Have a workshop clean or replace the control valve, and adjust the camshaft setting if needed
- 6If the fault returns: have a workshop check the camshaft and the VVT unit
Symptome, die Sie bemerken können5
- Engine is hard to start
- The car lacks power
- Engine hesitates or runs jerkily
- Emissions warning lamp lit
- Check engine lamp lit or behaving abnormally
Was der Fehler beeinflussen kann1
- Camshaft control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.