VOLVO
ECM-P003013 - HO2S Heater Control Circuit (Bank 1, Sensor 1). General Electrical Failures. Circuit open
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module controls the heating of the front lambda sensor on bank 1 by pulsing the current to the sensor's PTC element. The code concerns an open circuit and is set when the signal falls below a certain level while the heating is switched off.
Mögliche Ursachen
- Poor contact and oxidation in the connections
- Open circuit in the supply from the system relay
- Faulty front lambda sensor
Was Sie tun können
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the connector at the bank 1 lambda sensor for poor contact and oxidation, and do not use rust-release spray or grease in the connector
- 3Use a multimeter to check that the supply voltage between the system relay and the lambda sensor has no open circuit
- 4Have a workshop measure from the back of the connectors, so they are not damaged and do not develop loose contact later
- 5If troubleshooting does not solve the fault: have a workshop try a new lambda sensor
Symptome, die Sie bemerken können1
- Check engine lamp lit or behaving abnormally
Was der Fehler beeinflussen kann1
- Lambda control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.