VOLVO
ECM-P003613 - HO2S Heater Control Circuit (Bank 1, Sensor 2). General Electrical Failures. Circuit open
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module regulates the heating of the rear lambda sensor on bank 1, sensor 2, by pulsing the current to the sensor's PTC element. The code concerns an open circuit and is set when the signal falls below a set level while the heating is switched off.
Mögliche Ursachen
- Poor contact and oxidation in the connections
- Open circuit in the supply from the system relay
- Faulty rear lambda sensor
Was Sie tun können
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the connector at the rear lambda sensor for poor contact or oxidation, and do not use rust-release spray or grease in the connector
- 3Use a multimeter to check that the supply voltage from the system relay to the rear lambda sensor has no open circuit
- 4Have a workshop check the resistance of the lambda sensor
- 5If troubleshooting does not solve the fault: have a workshop try a new lambda sensor
Symptome, die Sie bemerken können1
- Check engine lamp lit or behaving abnormally
Was der Fehler beeinflussen kann1
- Lambda control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.