VOLVO
ECM-P006A62 - MAP - Mass or Volume Air Flow Correlation. Algorithm Based Failures. Signal compare failure
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module works out the expected air mass from several parameters and compares it with the reading from the mass air flow sensor. The code is set when the air mass correction factor drops too far while the lambda adaptation sits outside a set band.
Mögliche Ursachen
- Contact resistance or oxidation in the connectors of the mass air flow sensor
- Air leakage in the intake system
- Blocked intake system
- Damaged mass air flow sensor
Was Sie tun können
- 1Check the mass air flow sensor connector for contact resistance and oxidation
- 2Check the hoses between the mass air flow sensor and the throttle unit for leaks, damage and loose connections
- 3Check that the intake system is not blocked, for example by contamination in the throttle
- 4If you have a diagnostic tool, read the air mass in live data at idle and when the throttle is opened. The value should follow the throttle
- 5Have a workshop check the mass air flow sensor if the fault remains after checking the intake system
Symptome, die Sie bemerken können1
- Poor performance and lack of power while driving
Was der Fehler beeinflussen kann3
- A calculated boost pressure and a calculated air mass are used
- Control of the rear oxygen sensor is switched off
- The misfire diagnostic is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.