VOLVO
ECM-P007C11 - Charge Air Cooler Temperature Sensor Circuit Low (Bank 1). General Electrical Failures. Circuit short to ground
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The boost pressure sensor (TMAP) measures boost pressure and temperature at the charge air cooler. The fault code is set when the signal from the sensor is below a limit, which can be caused by a signal wire shorted to ground, poor contact or a damaged sensor.
Mögliche Ursachen
- Contact resistance, oxidation or loose connection in the connector
- Signal wire shorted to ground
- Damaged boost pressure sensor (TMAP)
Was Sie tun können
- 1Use a multimeter to check that the signal wire to the boost pressure sensor has no contact with ground (the body), with the ignition on
- 2Check the sensor connector for moisture, corrosion and loose connections
- 3Look for chafing in the sensor wiring, especially where it may have been pinched
- 4If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running and check whether it reads an unreasonably low value
- 5Have a workshop measure the sensor signal and replace the boost pressure sensor if the wiring is intact
Symptome, die Sie bemerken können1
- The Check engine warning lamp lights up
Was der Fehler beeinflussen kann1
- The engine control module uses a calculated value instead of the measured temperature
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.