VOLVO
ECM-P007D12 - Charge Air Cooler Temperature Sensor Circuit High (Bank 1). General Electrical Failures. Circuit short to battery
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The boost pressure sensor (TMAP) measures boost pressure and temperature at the charge air cooler. The fault code is set when the signal from the sensor is above a limit. The cause can be a signal wire shorted to voltage, an open circuit in the signal wire or a damaged sensor.
Mögliche Ursachen
- Open circuit in the signal wire to the boost pressure sensor
- Signal wire shorted to voltage
- Damaged boost pressure sensor (TMAP)
Was Sie tun können
- 1Use a multimeter to check that the signal wire to the boost pressure sensor has no voltage with the ignition off
- 2Check that the sensor connector is secure and not damaged
- 3Look for wiring that appears chafed or pinched at the sensor and along the route to it
- 4If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running and check whether it reads an unreasonably high value
- 5Have a workshop check the sensor if the wiring is intact and the fault remains
Symptome, die Sie bemerken können1
- The Check engine warning lamp lights up
Was der Fehler beeinflussen kann1
- The engine control module uses a calculated value instead of the measured temperature
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.