VOLVO
ECM-P010131 - Mass or Volume Air Flow A Circuit Range/Performance. FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures. No signal
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The ECM monitors the mass air flow sensor signal and compares it with the normal range. The code is stored when the signal is outside the normal range, and in this case no signal is received at all. The cause may be a broken wire, a short to ground or a faulty sensor.
Mögliche Ursachen
- Break in the signal wire
- Break in the voltage supply
- Signal wire shorted to ground
- Contact resistance in the mass air flow sensor connector terminals
- Damaged mass air flow sensor
Was Sie tun können
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check that the connector at the mass air flow sensor is fully engaged and free from corrosion
- 3With a multimeter, check that the voltage supply wire from the system relay to the sensor has no break
- 4With a multimeter, check that the signal wire between the control module and the sensor has continuity and is not shorted to ground
- 5If you have diagnostic equipment, read the air flow in live data at idle and check whether the value changes at all when the throttle is varied
- 6If the fault remains, have a workshop check the mass air flow sensor
Symptome, die Sie bemerken können1
- The car lacks power and runs poorly
Was der Fehler beeinflussen kann3
- A calculated air mass value is used instead of the measured value
- Rear lambda sensor control and misfire diagnosis are switched off
- Engine torque may be limited
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.