VOLVO
ECM-P010817 - Manifold Absolute Pressure/BARO Sensor High. General Electrical Failures. Circuit voltage above threshold
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The ECM measures the intake pressure with an air pressure sensor and checks the sensor's DC voltage. The code is stored when an incorrect value lasts for a set time or over three or more consecutive drive cycles.
Mögliche Ursachen
- Break in the signal or ground wire
- Contact resistance and oxidation in the connections
- Signal wire shorted to supply voltage
- Air pressure sensor in the intake pipe is damaged
Was Sie tun können
- 1Read and note the code, clear it and road test to see whether it returns
- 2With diagnostic equipment and the ignition on, compare the intake pressure in live data with ambient pressure; a clear difference suggests a faulty sensor
- 3Check that the connector at the sensor sits firmly and is free from oxidation and contact resistance
- 4With a multimeter, check that the signal wire is not shorted to supply voltage or ground
- 5If the fault remains and the sensor reading differs, have a workshop replace the sensor
Symptome, die Sie bemerken können1
- Engine warning lamp (check engine) lit or behaving abnormally
Was der Fehler beeinflussen kann1
- The sensor signal is replaced by a constant intake air pressure value
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.