VOLVO
ECM-P013716 - O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2). General Electrical Failures. Circuit voltage below threshold
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
Although the code is named for a low voltage, it concerns the signal from the rear oxygen sensor in bank 1, sensor 2. The engine control module (ECM) monitors the sensor signal and sets the code when it deviates from its permitted range, or when the sensor's pre-heating voltage disturbs the signal. The rear sensor is used to check that the catalytic converter is working.
Mögliche Ursachen
- Signal wire shorted to ground
- Ground wire shorted to ground
- Damaged rear oxygen sensor
Was Sie tun können
- 1Read the code, clear it and road test the car to see whether it comes back
- 2Use a multimeter to check that the signal wire to the rear sensor is not shorted to ground
- 3Check the connector to the rear sensor for contact resistance and oxidation; do not use rust solvent spray or grease
- 4If the wires and connector are intact, replace the rear oxygen sensor
Symptome, die Sie bemerken können1
- Check engine light (MIL) on
Was der Fehler beeinflussen kann2
- Control with the rear oxygen sensor is switched off
- Catalytic converter diagnostics are disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.