VOLVO
ECM-P013817 - O2 Sensor Circuit High Voltage (Bank 1 Sensor 2). General Electrical Failures. Circuit voltage above threshold
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The engine control module (ECM) monitors the rear oxygen sensor in bank 1, sensor 2, by checking its signal while driving. It sets the code when the signal deviates from its permitted operating range or when the pre-heating voltage disturbs the signal. The cause may therefore be wires that have picked up voltage instead of running to their correct point, or a damaged sensor.
Mögliche Ursachen
- Signal wire shorted to supply voltage
- Ground wire shorted to supply voltage
- Damaged rear oxygen sensor
Was Sie tun können
- 1Read the code, clear it and road test the car to see whether it comes back
- 2Switch the ignition off and use a multimeter to check that the signal wire from the rear sensor has no contact with voltage
- 3Check that the ground wire has no contact with voltage, and inspect the connectors for contact resistance
- 4If the wires are intact, replace the rear oxygen sensor
Symptome, die Sie bemerken können1
- Check engine light (MIL) on
Was der Fehler beeinflussen kann2
- Control with the rear oxygen sensor is switched off
- Catalytic converter diagnostics are disabled
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.