VOLVO
ECM-P022023 - Throttle/Pedal Position Switch B Circuit. General Signal Failures. Signal stuck low
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (30)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Nur Motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo S80 (2007–)2011–2012, 2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Nur Motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011–2012Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
Was bedeutet der Fehlercode?
Although the code is named switch B circuit, it applies to the signal from the accelerator pedal position sensor. The signal stays low for a longer period and therefore does not follow the pedal movement. The fault is first registered in the central electronic module (CEM), so the root fault may be there.
Mögliche Ursachen
- Signal wire shorted to ground
- Damaged accelerator pedal position sensor
- Fault in the central electronic module (CEM), which registers the fault first
Was Sie tun können
- 1Read the codes in all control modules, not only the engine control module. If a code is present in the CEM, deal with it first
- 2Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 3Look at the accelerator pedal connector and wiring for loose connections, corrosion and chafed areas
- 4Use a multimeter to check that the signal wire from the pedal is not shorted to ground
- 5If you have a diagnostic tool: check whether the accelerator pedal position in live data stays at the same low value when the pedal is pressed
- 6If the fault remains after these checks, have a workshop check the CEM and the accelerator pedal sensor with diagnostic equipment. The code is only cleared once the root fault is fixed
Symptome, die Sie bemerken können2
- Accelerator pedal ignored during braking
- Warning symbol and message in the display
Was der Fehler beeinflussen kann1
- When the brake pedal is pressed at the same time, the accelerator is treated as released
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.