VOLVO
ECM-P033122 - Knock Sensor 2 Circuit Range/Performance (Bank 2). General Signal Failures. Signal too high
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (24)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo S80 (2007–)2011–2012, 2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011–2012Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The signal from knock sensor 2 is too high compared with limits that depend on engine speed. The fault code is then set. The causes may be poor contact, a loose sensor or a damaged sensor. The fault is a general signal fault.
Mögliche Ursachen
- Contact resistance or oxidation at the knock sensor plug
- Loosely fitted knock sensor
- Damaged knock sensor
Was Sie tun können
- 1Read the fault code, clear it and take a short drive
- 2Check that knock sensor 2 is tightened down and has not worked loose
- 3Check the connection to knock sensor 2 for contact resistance and oxidation
- 4If you have a diagnostic tool: read the knock signal from sensor 2 in live data at idle and under throttle
- 5Have a workshop with diagnostic equipment replace knock sensor 2 if it is damaged
Symptome, die Sie bemerken können3
- Poor performance and lack of power, especially when pulling away from standstill
- The engine hesitates, surges or runs roughly during acceleration, slowing down and at constant speed
- Reduced performance
Was der Fehler beeinflussen kann1
- Ignition timing is retarded as a safety measure
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.