VOLVO
ECM-P033211 - Knock Sensor 2 Circuit Low (Bank 2). General Electrical Failures. Circuit short to ground
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The signal from the right knock sensor is too low. The engine control module (ECM) compares the signal with limits and sets the fault code when it deviates. A signal cable that has been short-circuited to ground is one possible cause. Poor contact, a break or a damaged sensor can produce the same fault code.
Mögliche Ursachen
- Signal cable short-circuited to ground
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
Was Sie tun können
- 1Read the fault code, clear it and test drive the car
- 2Check the signal cable from the right knock sensor for a short to ground; with a multimeter, confirm that the cable has no contact with the body
- 3Check the connections to the right knock sensor for contact resistance and oxidation
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether it is too low
- 5Have a workshop with diagnostic equipment check the wiring and replace the knock sensor if needed
Symptome, die Sie bemerken können1
- Poor performance and lack of power while driving
Was der Fehler beeinflussen kann2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.