VOLVO
ECM-P033312 - Knock Sensor 2 Circuit High (Bank 2). General Electrical Failures. Circuit short to battery
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The fault concerns a signal from the right knock sensor that is too high. A signal cable short-circuited to voltage is one possible cause. An incorrectly fitted sensor can also produce the same fault code.
Mögliche Ursachen
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
Was Sie tun können
- 1Read the fault code, clear it and test drive the car
- 2Check the signal cable from the right knock sensor where it could have touched the positive supply; with a multimeter, confirm that the cable has no contact with the positive supply
- 3Check that the right knock sensor is correctly fitted
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether it is too high
- 5Have a workshop with diagnostic equipment check the wiring and replace the knock sensor if needed
Symptome, die Sie bemerken können1
- Poor performance and lack of power while driving
Was der Fehler beeinflussen kann2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.