ECM-P033315
VOLVO
ECM-P033315 - Knock Sensor 2 Circuit High (Bank 2). General Electrical Failures. Circuit short to battery or open
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The signal from the right knock sensor is too high. The cause may be a signal cable short-circuited to voltage, but an open circuit, meaning a break, can also produce the fault code. An incorrectly fitted sensor may also be the cause.
Mögliche Ursachen
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
Was Sie tun können
- 1Read the fault code, clear it and test drive the car to see whether it returns
- 2Check that the cable to the right knock sensor is intact, with no breaks or chafing
- 3With a multimeter: confirm that the cable has no contact with the positive supply and that it is continuous along its whole length
- 4Check that the right knock sensor is firmly seated and correctly fitted
- 5Have a workshop with diagnostic equipment check the wiring to the sensor and replace the knock sensor if needed
Symptome, die Sie bemerken können1
- Poor performance and lack of power while driving
Was der Fehler beeinflussen kann2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.