VOLVO
ECM-P033900 - Crankshaft Position Sensor A Circuit Intermittent. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
13 ModelleC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (40)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4, D4162T
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4, D4162T
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5, D4162T
- Volvo S80 (2007–)2007Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2008–2009Nur Motor: B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6304T2, B6324S, B6324S2, B8444S, D4164T
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S, D4164T
- Volvo S80 (2007–)2012, 2015Nur Motor: B6304T4, B6324S4, B6324S5, D4162T
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5, D4162T
- Volvo V40 (2013–)2013Alle Motoren außer: B4164T, B4164T3, D5204T4, D5204T6
- Volvo V40 (2013–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, D4162T
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9, D4162T
- Volvo V40 Cross Country (2013–)2013–2014Alle Motoren außer: B4164T, D5204T4, D5204T6
- Volvo V40 Cross Country (2013–)2015Alle Motoren außer: B4164T, B4204T11, D4204T14, D5204T6
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4, D4162T
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4, D4162T
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4, D4162T
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D4162T
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Nur Motor: B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2, D4164T
- Volvo V70 (2008–)2011Nur Motor: B6304T4, B6324S5, D4164T
- Volvo V70 (2008–)2012Nur Motor: B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5, D4162T
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4, D4162T
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Nur Motor: B8444S
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Nur Motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module counts the teeth on the flywheel, or the holes in the carrier plate, using the crankshaft position sensor signal. The fault is stored when the count is wrong over a set number of crankshaft revolutions.
Mögliche Ursachen
- Signal wires have an open circuit or are shorted to ground or supply voltage
- Loose connections
- Contact resistance or oxidation in the connections
- Sensor fitted incorrectly or damaged
- Damage to the flywheel or carrier plate
Was Sie tun können
- 1If you have a diagnostic tool, start the engine, raise the speed and read the fault status. 'Fault found' means a permanent fault.
- 2Check that the fuses are intact.
- 3Use a multimeter to check that the signal wires to the sensor have no open circuit and no short to ground or supply voltage.
- 4Check that the connector at the sensor is secure and free from oxidation and contact resistance.
- 5Check that the sensor is correctly fitted. If the fault returns, have a workshop check the flywheel and carrier plate for damage.
- 6If you have a diagnostic tool, follow the engine speed in live data while the engine runs and check that the value is steady.
Symptome, die Sie bemerken können2
- Engine stalls
- Engine does not start and only cranks
Was der Fehler beeinflussen kann1
- The ECM may use the camshaft sensor signal instead
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.