VOLVO
ECM-P034400 - Camshaft Position Sensor A Circuit Intermittent (Bank 1 or single sensor). General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (36)
- Volvo S60 (2011–)2011–2012Nur Motor: B5254T5, B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007Alle Motoren außer: D5244T4, D5244T5
- Volvo S80 (2007–)2008Nur Motor: B5254T6, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2009Nur Motor: B5254T6, B5254T8, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Alle Motoren außer: B4204S3, B4204S4, B4204T6, D4204T, D5244T10, D5244T14, D5244T19
- Volvo S80 (2007–)2011Alle Motoren außer: B4164T, B4204S3, B4204S4, B4204T6, B4204T7, D5204T2, D5244T10
- Volvo S80 (2007–)2012Nur Motor: B5254T10, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008Nur Motor: B5254T6, B6304T2, B6324S
- Volvo V70 (2008–)2009Nur Motor: B5254T6, B5254T8, B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B5254T10, B5254T11, B6304T2, B6324S, B6324S2, D4164T
- Volvo V70 (2008–)2011Nur Motor: B5254T10, B5254T11, B6304T4, B6324S5, D4164T
- Volvo V70 (2008–)2012Nur Motor: B5254T10, B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The engine control module (ECM) reads the PWM signal from the camshaft sensor. The fault is stored when the signal is missing from time to time, or when the camshaft has too few segments over a set number of crankshaft revolutions. The code applies to the intake camshaft sensor on bank 1.
Mögliche Ursachen
- Camshaft sensor in the wrong position
- Damaged camshaft sensor
- Loose connections
- Contact resistance and oxidation in the connections
- Open circuit or short circuit to ground or supply voltage in the signal wire
- Camshaft sensor fitted incorrectly
Was Sie tun können
- 1If you have a diagnostic tool, start the engine, raise the speed and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the camshaft sensor is clean, secure and free from contact resistance and oxidation.
- 4Check that the camshaft sensor is correctly fitted and that the housing around it is not damaged, since that can affect its position.
- 5If your diagnostic tool shows it, read the camshaft sensor position or speed in live data while the engine runs.
- 6If the fault returns, have a workshop check the camshaft sensor and its signal wire.
Symptome, die Sie bemerken können5
- Engine is hard to start
- Check engine light (emissions warning lamp) is on
- Automatic engine start/stop does not work
- Car lacks power
- Car hesitates or jerks while driving
Was der Fehler beeinflussen kann3
- The ECM uses the crankshaft sensor signal instead
- Variable valve timing (VVT) control is blocked
- Camshaft control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.