VOLVO
ECM-P034500 - Camshaft Position Sensor A Circuit (Bank 2). General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (21)
- Volvo S60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo S60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007–2009Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo V60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo V60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2008–2009Nur Motor: B6324S
- Volvo V70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo V70 (2008–)2011–2014Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B6304T4
- Volvo XC60 (2009–)2010Nur Motor: B6324S, B6324S2
- Volvo XC60 (2009–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008–2009Nur Motor: B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Nur Motor: B8444S
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Nur Motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The engine control module (ECM) reads the gear wheel on the camshaft through the camshaft sensor. The code is set when the ECM counts too few segments over a set number of crankshaft revolutions. It applies to the intake camshaft sensor on bank 2, the cylinder bank at the rear.
Mögliche Ursachen
- Open circuit in the signal cable
- Signal cable short circuit to ground
- Signal cable short circuit to supply voltage
- Damaged camshaft sensor
Was Sie tun können
- 1If you have a diagnostic tool, start the engine, raise the engine speed a few times and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the bank 2 camshaft sensor is secure and clean.
- 4Use a multimeter to check that the signal wire to the bank 2 camshaft sensor has no open circuit and is not shorted to ground or supply voltage.
- 5If your diagnostic tool shows it, read the bank 2 camshaft sensor in live data while the engine runs.
- 6If the fault returns, have a workshop check the bank 2 camshaft sensor and its wiring.
Symptome, die Sie bemerken können5
- Car lacks power, especially when pulling away from standstill
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks when slowing down
- Check engine light is on or behaves abnormally
Was der Fehler beeinflussen kann2
- The ECM uses the crankshaft sensor signal instead
- Camshaft control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.