VOLVO
ECM-P034600 - Camshaft Position Sensor A Circuit Range/Performance (Bank 2). General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (21)
- Volvo S60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo S60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007–2009Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo V60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo V60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2008–2009Nur Motor: B6324S
- Volvo V70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo V70 (2008–)2011–2014Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B6304T4
- Volvo XC60 (2009–)2010Nur Motor: B6324S, B6324S2
- Volvo XC60 (2009–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008–2009Nur Motor: B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2005–2006Nur Motor: B8444S
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S, B8444S
- Volvo XC90 (2003–)2011Nur Motor: B6324S5, B8444S
- Volvo XC90 (2003–)2012–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The code applies to the intake camshaft sensor on bank 2. The engine control module (ECM) counts the segments on the camshaft gear wheel, and the fault is stored when the count is wrong over two crankshaft revolutions, which is one camshaft revolution. The code does not say which type of fault it is.
Mögliche Ursachen
- Wiring or connector fault that comes and goes
- Camshaft sensor fitted incorrectly
- Damaged camshaft sensor
Was Sie tun können
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the camshaft sensor connector is free from contact resistance and oxidation, and that the sensor is correctly fixed.
- 4Check that the wiring to the bank 2 camshaft sensor has no chafing or loose connectors, since a wiring fault can come and go.
- 5If your diagnostic tool shows it, read the bank 2 camshaft sensor in live data while the engine runs.
- 6If the fault returns, have a workshop check the camshaft sensor and its wiring.
Symptome, die Sie bemerken können4
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks at steady speed
- Check engine light is on or behaves abnormally
Was der Fehler beeinflussen kann2
- The ECM uses the crankshaft sensor signal instead
- Camshaft control is switched off
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.