VOLVO
ECM-P034900 - Camshaft Position Sensor A Circuit Intermittent (Bank 2). General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (19)
- Volvo S60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo S60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2007–2009Nur Motor: B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B6304T4, B6324S4, B6324S5, B8444S
- Volvo S80 (2007–)2012–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo V60 (2011–)2011–2014Nur Motor: B6304T4
- Volvo V60 (2011–)2015Nur Motor: B6304T3, B6304T4, B6304T5
- Volvo V70 (2008–)2008–2009Nur Motor: B6324S
- Volvo V70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo V70 (2008–)2011–2014Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B6304T4
- Volvo XC60 (2009–)2010Nur Motor: B6324S, B6324S2
- Volvo XC60 (2009–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2008–2009Nur Motor: B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6324S, B6324S2
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
The fault is recorded as intermittent, meaning it comes and goes, and it may not be present right now. The fault applies to the intake camshaft sensor on bank 2. The engine control module (ECM) reads the gear wheel on the camshaft through the sensor, and the fault is stored when the ECM counts too few segments over a set number of crankshaft revolutions.
Mögliche Ursachen
- Contact resistance and oxidation in the connections
- Open circuit in the signal cable
- Signal cable short circuit to supply voltage
- Signal cable short circuit to ground
- Camshaft sensor fitted incorrectly
- Damaged camshaft sensor
Was Sie tun können
- 1If you have a diagnostic tool, start the engine, raise the engine speed a few times and read the fault status. 'Fault found' means a permanent fault.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the bank 2 camshaft sensor is secure and free from oxidation.
- 4Check that the bank 2 camshaft sensor is correctly fitted and not damaged.
- 5If your diagnostic tool shows it, read the bank 2 camshaft sensor in live data while the engine runs.
- 6After a repair, read the fault status again to confirm that the fault is gone.
Symptome, die Sie bemerken können5
- Malfunction indicator light (MIL) is on
- Car lacks power, especially when pulling away from standstill
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks when slowing down
Was der Fehler beeinflussen kann2
- The ECM uses the crankshaft sensor signal instead
- Variable valve timing (VVT) control is blocked
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.