VOLVO
ECM-P035500 - Ignition Coil E Primary/Secondary Circuit. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
6 ModelleS60 (2011–), S80 (2007–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (19)
- Volvo S60 (2011–)2011–2012Nur Motor: B5254T5
- Volvo S80 (2007–)2007Alle Motoren außer: D5244T4, D5244T5
- Volvo S80 (2007–)2008Nur Motor: B5254T6, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2009Nur Motor: B5254T6, B5254T8, B6304T2, B6324S, B8444S
- Volvo S80 (2007–)2010Nur Motor: B5254T10, B5254T11, B5254T8, B6304T2, B6324S, B6324S2, B8444S
- Volvo S80 (2007–)2011Nur Motor: B5254T10, B5254T11, B5254T8, B8444S
- Volvo S80 (2007–)2012Nur Motor: B5254T10
- Volvo V70 (2008–)2008Nur Motor: B5254T6, B6304T2, B6324S
- Volvo V70 (2008–)2009Nur Motor: B5254T6, B5254T8, B6304T2, B6324S
- Volvo V70 (2008–)2010Nur Motor: B5254T10, B5254T11, B6304T2, B6324S, B6324S2
- Volvo V70 (2008–)2011Nur Motor: B5254T10, B5254T11
- Volvo V70 (2008–)2012Nur Motor: B5254T10
- Volvo XC60 (2009–)2009Nur Motor: B6304T2
- Volvo XC60 (2009–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC70 (2008–)2008Nur Motor: B6324S
- Volvo XC70 (2008–)2009Nur Motor: B6304T2, B6324S
- Volvo XC70 (2008–)2010Nur Motor: B6304T2, B6324S, B6324S2
- Volvo XC90 (2003–)2005–2006, 2011Nur Motor: B8444S
- Volvo XC90 (2003–)2007–2010Nur Motor: B6324S, B8444S
Was bedeutet der Fehlercode?
The code applies to ignition coil E, which is the coil for cylinder 5. It shows which coil is affected but not which type of fault it is. The engine control module (ECM) checks the coils' function through a separate diagnostic line.
Mögliche Ursachen
- Contact resistance and oxidation at the coil connector
- Signal wire short circuit to ground or supply voltage
- Open circuit in the signal wire
- Open circuit in the supply wire
- Diagnostic line short circuit to ground or supply voltage
- Damaged ignition coil
Was Sie tun können
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check the connector to the ignition coil for cylinder 5 for contact resistance and oxidation.
- 4Use a multimeter to check that the wires to the ignition coil for cylinder 5 have no open circuit and are not shorted to ground or supply voltage.
- 5Check that the ignition coil is secure and not damaged.
- 6If the fault returns, have a workshop check the ignition coil for cylinder 5 and its diagnostic line.
Symptome, die Sie bemerken können5
- Engine misfires
- Check engine light (emissions warning lamp) is on
- Engine is not firing on all cylinders
- Car lacks power, especially when pulling away from standstill
- Car hesitates or jerks when slowing down
Was der Fehler beeinflussen kann1
- Closed loop control of lambda is blocked
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.