VOLVO
ECM-P035513 - Ignition Coil E Primary/Secondary Circuit. General Electrical Failures. Circuit open
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
10 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo S60 (2011–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T4
- Volvo S60 (2011–)2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5
- Volvo S80 (2007–)2011–2012, 2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo S80 (2007–)2013–2014Nur Motor: B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo V40 (2013–)2013–2014Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V40 (2013–)2015Nur Motor: B5204T8, B5204T9
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B5204T8, B5204T9, B5254T12, B5254T14
- Volvo V60 (2011–)2011–2012Nur Motor: B6304T4
- Volvo V60 (2011–)2013Nur Motor: B5204T8, B5204T9, B6304T4
- Volvo V60 (2011–)2014Nur Motor: B5204T8, B5204T9, B5254T12, B6304T4
- Volvo V60 (2011–)2015Nur Motor: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2011–2012Nur Motor: B6304T4, B6324S5
- Volvo V70 (2008–)2013–2014Nur Motor: B5204T9, B6304T4, B6324S5
- Volvo V70 (2008–)2015Nur Motor: B5204T9, B6304T4
- Volvo XC60 (2009–)2011–2014Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2015Nur Motor: B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2011–2015Nur Motor: B6304T4, B6324S4, B6324S5
- Volvo XC90 (2003–)2011–2014Nur Motor: B6324S5
Was bedeutet der Fehlercode?
Ignition coil E has an open circuit in its signal wire, according to the code. The code is stored when the open circuit persists over several driving cycles in a row, and it concerns the primary and secondary circuit of the coil.
Mögliche Ursachen
- Contact resistance and oxidation in the connections
- Open circuit in the signal wire
- Damaged ignition coil
Was Sie tun können
- 1If you have a diagnostic tool, start the engine and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check the connector at ignition coil E for contact resistance and oxidation.
- 4Use a multimeter to check that the signal wire to ignition coil E has no open circuit.
- 5Check that the wire to ignition coil E is not twisted, pinched or chafed.
- 6If the fault returns, have a workshop check ignition coil E and its diagnostic line.
Symptome, die Sie bemerken können4
- Engine lacks power, especially when pulling away from standstill
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks at steady speed
Was der Fehler beeinflussen kann1
- Closed loop control of lambda is blocked
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.