VOLVO
ECM-P036711 - Camshaft Position Sensor B Circuit Low (Bank 1). General Electrical Failures. Circuit short to ground
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Gilt für folgende Modelle:
7 ModelleS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Modelle nach Baujahr und Motor anzeigen (20)
- Volvo S60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo S60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo S60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo S80 (2007–)2010Nur Motor: B4204T6
- Volvo S80 (2007–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo S80 (2007–)2012–2014Nur Motor: B4164T, B4164T2, B4204T6, B4204T7
- Volvo S80 (2007–)2015Nur Motor: B4164T
- Volvo V40 (2013–)2013Nur Motor: B4164T, B4164T3
- Volvo V40 (2013–)2014–2015Nur Motor: B4164T, B4164T3, B4164T4
- Volvo V40 Cross Country (2013–)2013–2015Nur Motor: B4164T
- Volvo V60 (2011–)2011Nur Motor: B4164T, B4164T3, B4204T6, B4204T7
- Volvo V60 (2011–)2012–2014Nur Motor: B4164T, B4164T2, B4164T3, B4204T7
- Volvo V60 (2011–)2015Nur Motor: B4164T, B4164T2, B4164T3
- Volvo V70 (2008–)2010Nur Motor: B4204T6
- Volvo V70 (2008–)2011Nur Motor: B4164T, B4204T6, B4204T7
- Volvo V70 (2008–)2012–2014Nur Motor: B4164T, B4164T2, B4204T7
- Volvo V70 (2008–)2015Nur Motor: B4164T, B4164T2
- Volvo XC60 (2009–)2010Nur Motor: B4204T6
- Volvo XC60 (2009–)2011–2012Nur Motor: B4204T6, B4204T7
- Volvo XC60 (2009–)2013–2015Nur Motor: B4204T7
Was bedeutet der Fehlercode?
The fault is a short circuit to ground, and the signal from the exhaust camshaft sensor on bank 1 is constantly low while the engine runs. The engine control module (ECM) registers this as a fault.
Mögliche Ursachen
- Signal wire short circuit to ground
- Open circuit in the supply wire
- Loose connections
Was Sie tun können
- 1If you have a diagnostic tool, start the engine and read the fault status. 'No fault found' means the fault is not active right now.
- 2Check that the fuses are intact.
- 3With the ignition off, check that the connector at the exhaust camshaft sensor on bank 1 is secure and free from oxidation.
- 4Use a multimeter to check that the signal wire has no contact with ground (the body).
- 5Check that the supply wire to the exhaust camshaft sensor is not broken.
- 6If the fault returns, have a workshop check the exhaust camshaft sensor and its wiring.
Symptome, die Sie bemerken können2
- Engine does not start, sometimes or every time
- Engine is hard to start and cranks slowly
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.