VOLVO
ECM-P038400 - Glow Plug Control Module 1 Control Circuit High. General Failure Information. No sub type information
System
Motorsteuergerät (ECM)
Volvo-Modelle, für die dieser Fehlercode gilt
Dieser Fehlercode hat je nach Modell, Modelljahr oder Motor unterschiedliche Bedeutungen. Wählen Sie die Bedeutung, die für Ihr Fahrzeug gilt.
Gilt für folgende Modelle:
11 ModelleC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Modelle nach Baujahr und Motor anzeigen (17)
- Volvo C30 (2007–2013)2011–2013Nur Motor: D4162T
- Volvo S40 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo S60 (2011–)2011–2013Nur Motor: D4162T
- Volvo S60 (2011–)2014–2015Nur Motor: D4162T, D4204T5
- Volvo S80 (2007–)2012–2013Nur Motor: D4162T
- Volvo S80 (2007–)2014–2015Nur Motor: D4162T, D4204T5
- Volvo V40 (2013–)2013–2014Nur Motor: D4162T
- Volvo V40 (2013–)2015Nur Motor: D4162T, D4204T14
- Volvo V40 Cross Country (2013–)2013–2014Nur Motor: D4162T
- Volvo V40 Cross Country (2013–)2015Nur Motor: D4162T, D4204T14
- Volvo V50 (2004–2013)2011–2012Nur Motor: D4162T
- Volvo V60 (2011–)2011–2013Nur Motor: D4162T
- Volvo V60 (2011–)2014–2015Nur Motor: D4162T, D4204T5
- Volvo V70 (2008–)2012–2013Nur Motor: D4162T
- Volvo V70 (2008–)2014–2015Nur Motor: D4162T, D4204T5
- Volvo XC60 (2009–)2014–2015Nur Motor: D4204T5
- Volvo XC70 (2008–)2014–2015Nur Motor: D4204T5
Was bedeutet der Fehlercode?
The ECM powers the glow plugs through the GCU and its built-in relay. The fault is set when a signal that is too high in the control circuit. It can be caused by the signal cable touching the supply voltage, or by a fault in the power supply or charging system.
Mögliche Ursachen
- Signal cable short-circuited to supply voltage
- Glow plug power supply cable short-circuited to supply voltage
- Damaged glow plug relay
- Damaged power supply or charging system
- This code may be a follow-on fault from ECM-P056300 and ECM-P056100
Was Sie tun können
- 1Check that the fuses are intact; their locations are in the instruction manual or the fuse chart
- 2Read and clear the fault code, then cold-start the engine and see whether it comes back
- 3If the codes ECM-P056300 or ECM-P056100 are present, deal with them first, since this code may be a follow-on fault from them
- 4Check that the battery is charged and that the charging works, since the power supply is among the possible causes
- 5Measure with a multimeter whether the signal cable to the glow plug control module has voltage with the ignition off, which would point to a short to the supply
- 6If you have a diagnostic tool, activate the glow function and check that the glow relay engages
Symptome, die Sie bemerken können2
- Engine is hard to start or cranks slowly on cold starts
- Starting problems at all times, or it is unclear when they occur
Was der Fehler beeinflussen kann1
- The glow plugs are deactivated
Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.