Zum Inhalt springen
    OBD Tuning
    SENDEN SIE AN UNS
    SENDEN SIE AN UNS
    Startseite
    Fehlercodes
    VOLVO
    ECM-P039400
    VOLVO

    ECM-P039400 - Camshaft Position Sensor B Circuit Intermittent (Bank 2). General Failure Information. No sub type information

    System

    Motorsteuergerät (ECM)

    Volvo-Modelle, für die dieser Fehlercode gilt

    Gilt für folgende Modelle:

    1 Modell

    S80 (2007–)

    Modelle nach Baujahr und Motor anzeigen (1)
    • Volvo S80 (2007–)2007–2011Nur Motor: B8444S

    Was bedeutet der Fehlercode?

    The fault is intermittent, which means it has occurred at an earlier time but may not be present at the moment. The engine control module (ECM) reads the teeth of a toothed wheel on the camshaft via the camshaft position sensor for the exhaust camshaft on bank 2. The fault is set when the control module detects too few segments over a certain number of crankshaft revolutions.

    Mögliche Ursachen

    • Contact resistance or oxidation in the connections
    • Open circuit in the signal cable
    • Signal cable short-circuited to supply voltage
    • Signal cable short-circuited to ground
    • Camshaft position sensor fitted incorrectly
    • Damaged camshaft position sensor

    Was Sie tun können

    1. 1If you have a diagnostic tool, read the fault status after the engine has run: Fault found means a permanent fault, No fault found means it is not active now
    2. 2Check that the camshaft position sensor is firmly fitted and in the correct position
    3. 3Check the connections to the camshaft position sensor for contact resistance and oxidation
    4. 4Check the wiring to the camshaft position sensor for chafing and pinching
    5. 5Measure with a multimeter that the signal cable has no contact with ground or supply voltage, and that the supply and ground wires have no open circuit
    6. 6After a repair, check that the diagnosis completes and that the fault status shows No fault found

    Symptome, die Sie bemerken können1

    • The Check engine (malfunction indicator) light comes on or behaves abnormally

    Was der Fehler beeinflussen kann2

    • The control module uses the signal from the engine speed sensor instead
    • The variable valve timing (VVT) control is blocked

    Allgemeine Hinweise für Fahrzeughalter. Die Diagnose am Fahrzeug kann eine andere Ursache zeigen.

    OBD Tuning

    Schwedens führendes Kompetenzzentrum für Automotorelektronik. Wir bieten professionelle ECU-Optimierung, Steuergerätereparatur und Diagnose mit 12-monatiger Garantie.

    Dienstleistungen

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    Datenbank & Diagnose

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    ECU-Hersteller

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Unternehmen

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    • Motoroptimierung
    • ECU-Reparatur
    • Modul-Klonen
    • Kombiinstrument
    • SRS / Airbag
    • Wegfahrsperre

    • ECU-Datenbank
    • DTC Fehlercodekatalog
    • Diagnoseanleitungen & Messwerte
    • KI-Fehlercode-Analysator
    • Neuigkeiten

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • Über uns
    • Kontakt
    • Workshop-Partner
    • Versandanleitung
    • Garantie
    • Häufig gestellte Fragen
    • AGB
    • Datenschutz
    • Sitemap

    Besuchen Sie uns

    Gjuterigatan 29, Karlstad

    Rufen Sie uns an

    054-830 480

    Schreiben Sie uns eine E-Mail

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. Alle Rechte vorbehalten.